Automotive On-board diagnostic systems of thesedays have gone a long way toward helping you locate a problem. But those systems aren't perfect and they don't cover everything (most glitches and intermittents). So the real challenge that befuddles most automotive technicians is diagnosing "no-code" trouble. On-board diagnostic systems are engineered with fairly wide set limits for sensors, actuators, connectors and terminals. When a component exceeds its limit consistently, a trouble code is generated. But to keep warranty costs in line, tolerances aren't set to catch all transients, even though they can cause some of your worst headaches. As a result, technicians are finding more and more uses for the oscilloscope - next to the multimeter, the most common troubleshooting tool.

The 1006 Automotive Scope/GMM/OBD II Code Reader represents the most powerful and versatile tool available for troubleshooting automotive electronics since we can track down elusive no-code driveability problems as well as diagnose OBD II sensors and components.

Features: 

- A 25 Mega-sample/Second (one channel minimum) sample rate for rapid data updates.

- Lab scope signal patterns.

- True RMS Graphing Multimeter (GMM) measurements and graphs.

- OBD II (EOBD) Code Reader function.

- A unique "Glitch Snare" mode which captures, displays and optionally saves abnormal signal patterns in the Scope mode of the COMPONENT TESTS only when they occur.

- Preset tests that enable the user to check the majority of automotive sensors, actuators and systems easily and quickly.

- Powerful built-in reference information for each preset test which includes a test procedure showing how to connect to the circuit, a normal reference signal pattern, theory of operation and troubleshooting tips.

- Menu-driven interface has automatic configurations for most of non-preset tests, so you will find that the instrument is easy-to-use.

- The Secondary Ignition Single function displays the waveform along with the spark voltage, RPM, burn time and burn voltage.

- The Diesel function allows you to set injection pump timing and RPM using the optional Diesel accessories.

- USB interface supports updates for code and data.

Accessories:

 - Ni-MH Rechargeable Battery(1.2Vx5) Pack - BT10

- Shielded Test Leads (Red, Yellow) - FSTL 1000

- Ground Leads for Shielded Test Leads (Black) - FSTL 1000G

- Alligator Clips (Red, Yellow, Black) - AC5W

- Back Probe Pins (Red, Yellow, Black) - BPP 1000

- 2 mm Adaptors (Red, Yellow, Black) - FSA 2

- Secondary Capacitive Pick-up - SIP 1000

- Ground Leads for Secondary Probe - SIP 1000G

- Inductive Pick-up - RPM 206

- AC to DC Power Adaptor - PA 1000

- OBD II Code Reader Cable - 1006 OBD 2

- Soft Carrying Case - S3C

- User’s Manual (Paper) - FUM 1006

Electrical Specification

Accuracies is given as ±(% of reading + number of least significant digits) at 18°C to 28°C with relative humidity up to 80%, for a period of one year after calibration.

Scope Specifications

Horizontal

 - Sample rate : 25 Mega sample/second

- Record length : 1000 Points

- Update rate : Real time, Roll

- Accuracy : ± (0.1 % + 1 pixel)

- Sweep rate : 1 µs to 50 sec in a 1, 2, 5 sequence (Scope mode)

- 5 s to 24 Hours in a 1, 2, 5 sequence (GMM mode)

Vertical

- Band width : DC to 5 MHz ; -3 dB

- Resolution : 8 bit

- Channel : 2 Channel

- Coupling : AC, DC, GND

- Input Impedance : 1 Mohm / 70 pF

- Maximum Input Voltage : 300 V

- Volt/Division : 50 mV to 100 V in a 1, 2, 5 sequence

- Accuracy : ± 3 %

Trigger

- Trigger Source : CH A, CH B, TRIGGER (External trigger)

- Sensitivity (CH A) : < 1.0 div to 5 MHz

- Sensitivity (Trigger) : 0.2 V p-p

- Modes : Single shot, Normal, Auto

- Coupling : AC, DC

- Slope : Rising and falling edge

Others

- Glitch Snare : SCOPE Mode (Component test only)

- Acquire Mode : SCOPE Mode

- Setup memory : 8 Waveform & Setup

- Reference waveform : 51 Waveform and Setup

- Cursor : Time and Volt

- Instrument Setup : Language, Contrast, Graticule

Graphing Multimeter (GMM) Specifications

DC Voltage Measurement

AC Voltage Measurement

AC+DC Voltage Measurement

RPM Measurement

Frequency Measurement

Ohm Measurement

Continuity Test

Diode Test

Temperature Measurement

DC Ampere Measurement (Current Probe Output)

AC Ampere Measurement (Current Probe Output)

Optional Accessories:

 - USB Interface Kit(USB Cable + Firmware Loader Disc) - USB 1000

- Temperature Probe - TP 10

- mA Current Probe - CA113 OS/AT

- Diesel Interface Probe - DPS 1000

- Waveform Manager (CD) - WFM 1000

- Isolated 12 V Charger - PC 1000/12

- Isolated 24 V Charger - PC 1000/24

- User’s Manual (CD) - FUM 1006 CD

Standards

 - CAT II 300V

- IEC 1010-1

- UL 3111-1

- C22.2 No. 1010-1

- UL-Listed

- CE-mark